Victron SmartSolar Bundle with SmartSolar MPPT 100/20 with BMV-712 Smart Battery Monitor & Sense Cables, 5 Year Warranty
Victron SmartSolar Bundle with SmartSolar MPPT 100/20 with BMV-712 Smart Battery Monitor & Sense Cables, 5 Year Warranty. Pack Includes: Victron SmartSolar MPPT 100/20 - 12/24/48V Charge Controller - SCC110020160R Victron Battery Monitor BMV-712 Smart - BAM030712000R Victron Temperature Sensor for BMV-702/712 - ASS000100000 Victron Smart Battery Sense Long Range (up to 10m) - SBS050150200 Victron SmartSolar MPPT 100/20 - 12/24/48V Charge Controller Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life. Improves battery charging By measuring voltage at the battery bank terminals, errors arising from voltage-loss due to cable resistance are avoided - guaranteeing the correct charge-voltage. For lead batteries, battery temperature data is used to adjust the charge-voltages: cold batteries require an increased charge-voltage, whereas hot batteries require a decreased charge-voltage. For lithium batteries temperature data is used to disable charging when they are too cold: charging lithium batteries near or below freezing causes permanent damage to the cells. No wires The connection between Smart Battery Sense and one or more Solar Charger(s) is wireless: It uses VE.Smart Network - a wireless technology based on Bluetooth Smart. Information transmitted can be used simultaneously by one, two or more Solar Chargers connected to the same 12V, 24V and 48V battery bank. The Smart Network is set up using the VictronConnect app. Tidy, simple & smart Installation is simple, quick and tidy. Just connect the unit's two eyelets to your battery terminals and attach the Smart Battery Sense unit directly onto the battery-body using its self-adhesive strip. Features: Up to 10 metres in length. Improves battery charging. Bluetooth connection. Quick installation. Victron Battery Monitor BMV-712 Smart With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Bluetooth inside: With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance. Download the Victron Bluetooth app: Use a smartphone or other Bluetooth enabled device to customize settings, monitor all important data on single screen, view historical data, and to update the software when new features become available. Easy to install: All electrical connections are to the quick connect PCB on the current shunt. The shunt connects to the monitor with a standard RJ12 telephone cable. Included: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components needed. Also included are a separate front bezel for a square or round display appearance, a securing ring for rear mounting and screws for front mounting. Midpoint voltage monitoring: One bad cell or one bad battery can destroy a large, expensive battery bank. When batteries are connected in series, a timely warning can be generated by measuring the midpoint voltage. Please see the BMV manual, section 5.2, for more information. Victron recommend their Battery Balancer (BMS012201000) to maximize service life of series-connected lead-acid batteries. Very low current draw from the battery: Current consumption: 0,7Ah per month (1mA) @12V and 0,6Ah per month (0,8mA) @ 24V Especially Li-ion batteries have virtually no capacity left when discharged until low voltage shutdown. After shutdown due to low cell voltage, the capacity reserve of a Li-ion battery is approximately 1Ah per 100Ah battery capacity. The battery will be damaged if the remaining capacity reserve is drawn from the battery. A residual current of 10mA for example may damage a 200Ah battery if the system is left in discharged state during more than 8 days. Bi-stable alarm relay: Prevents increased current draw in case of an alarm. Other features: Battery voltage, current, power, ampere-hours consumed and state of charge Remaining time at the current rate of discharge Programmable visual and audible alarm Programmable relay, to turn off non critical loads or to run a generator when needed 500 Amp quick connect shunt and connection kit Shunt selection capability up to 10.000 Amps VE.Direct communication port Stores a wide range of historical events, which can be used to evaluate usage patterns and battery health Wide input voltage range: 6,5 – 70V High current measurement resolution: 10 mA (0,01A) Additional input to measure voltage (of a second battery), temperature or midpoint voltage, and corresponding alarm and relay settings Victron Temperature Sensor for BMV-702/712 Temperature sensor for BMV-702 and BMV-712 Smart battery monitor. This sensor will only work with the BMV-702 and BMV-712 battery monitors. NOTE: The Installation instructions will be found in the BMV Manual. When using the temperature sensor - the second battery voltage and midpoint voltage monitoring are not available. Victron Smart Battery Sense Long Range (up to 10m) Victron Smart Battery Sense Long Range (up to 10m). Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life. Improves battery charging By measuring voltage at the battery bank terminals, errors arising from voltage-loss due to cable resistance are avoided - guaranteeing the correct charge-voltage. For lead batteries, battery temperature data is used to adjust the charge-voltages: cold batteries require an increased charge-voltage, whereas hot batteries require a decreased charge-voltage. For lithium batteries temperature data is used to disable charging when they are too cold: charging lithium batteries near or below freezing causes permanent damage to the cells. No wires The connection between Smart Battery Sense and one or more Solar Charger(s) is wireless: It uses VE.Smart Network - a wireless technology based on Bluetooth Smart. Information transmitted can be used simultaneously by one, two or more Solar Chargers connected to the same 12V, 24V and 48V battery bank. The Smart Network is set up using the VictronConnect app. Tidy, simple & smart Installation is simple, quick and tidy. Just connect the unit's two eyelets to your battery terminals and attach the Smart Battery Sense unit directly onto the battery-body using its self-adhesive strip. Features: Up to 10 metres in length. Improves battery charging. Bluetooth connection. Quick installation.
Price: $619.00 from My Generator
